Refer to that product’s installation sheet for instructions. Twist and take away mounting bracket to insert battery. Product Description Lutron’s ceiling-mounted Occupancy Sensors are wireless, battery-powered, passive infrared (PIR) devices that mechanically control lights through RF communication with a dimming or switching system. These Sensors detect the heat from people transferring within an area to determine when the space is occupied. The Sensors then transmit the suitable commands to the associated dimming or switching device to turn the lights on or off routinely, providing each convenience and distinctive vitality savings. Sensor doesn't perform satisfactorily from this location, it may be moved to 1.4 Ifanother location by pulling the Sensor straight down and repeating steps 1.Three and 1.4. 1.5 If the Sensor’s efficiency is passable, it should be permanently hooked up to the ceiling tile, as described in part G. Everlasting Mounting. Short-term Solid Ceiling Mounting Use this procedure if the Sensor shall be mounted on a stable, steady ceiling surface resembling drywall, plaster, concrete, or wood. Two 3M™ Command™ adhesive strips are provided for briefly mounting and testing the Sensor on clean, strong ceiling surfaces. These strips are designed for simple, damagefree elimination and aren't reusable. These strips shouldn't be used for completely mounting the Sensor (see part G. Everlasting Mounting ). Carefully comply with the removal directions beneath to make sure the ceiling will not be broken during removing. Observe: Don't use the adhesive strips on ceiling tiles, as they will likely trigger harm to the tile upon removing. Simple-to-observe Instructions Set-Up In order for the Sensor to function correctly, it must first be arrange with a corresponding dimming or switching gadget. The process for establishing a Sensor with a Maestro Wireless® (MRF2- solely) Dimmer or Electronic Swap is detailed under. P/N 041-172a 2.1 Peel the purple "Command Strips" liner off of one of many adhesive strips and apply the strip to the flat aspect of the mounting bracket as proven in the diagram. Notice: Do not cover the bracket’s screw holes as a result of they are going to be used to mark screw hole areas on the ceiling. Establishing a Sensor with a Maestro Wireless Dimmer or Digital Change Dimmer Key Features · Low Upkeep. 10-year battery life. Handy low-battery indicator. · A number of Gadgets. Up to three Sensors can work collectively to regulate lights for broader protection in large areas. Every Sensor may be added to up to 10 receiving devices. Sensor Operation Occupancy Model - The Sensor will mechanically turn the lights on when the space is occupied and robotically flip the lights off after the space is vacated. The Sensor will mechanically turn the lights off after the house is vacated. There is a built-in 15-second vacancy grace period that begins when the lights are robotically turned off, throughout which the lights will automatically flip again on in response to motion. This grace interval is supplied as a safety and convenience function in the occasion that the lights flip off while the room is still occupied, in order that the consumer doesn't need to manually flip the lights again on. After 15 seconds, the grace interval expires and the lights must be manually turned on. This Sensor is part of a system and cannot be used to control a load with no suitable dimming or switching system. Check with the instruction sheets of the receiving device(s) for installation data. The Sensor may be put in as much as 60 ft (18.Three m) away from the associated dimming or switching device(s) if they're in direct line of sight. If there are partitions or other barriers between the Sensor and receiving machine(s), the Sensor ought to be positioned inside 30 ft (9.1 m). Caution: This product must not be used to manage gear which could create hazardous conditions, resembling entrapment, if operated by accident. Sensor in a location where it has a broad view outside the intended area. If this is unavoidable, the lens might be masked to block the view of undesired areas (seek advice from part I. Lens Masking). This guarantee is in lieu of all different specific warranties, and the implied warranty of merchantability is restricted to at least one year from buy. This guarantee does not cowl the cost of installation, removing or reinstallation, or harm resulting from misuse, abuse, or harm from improper wiring or installation. This warranty doesn't cover incidental or consequential damages. LUTRON’S Legal responsibility ON ANY Declare FOR DAMAGES ARISING OUT OF OR IN CON­NEC­TION WITH THE MANUFACTURE, SALE, Set up, Delivery, OR USE OF THE UNIT SHALL Never EXCEED THE PUR­CHASE Price OF THE UNIT. This warranty gives you particular authorized rights, and you might have other rights which range from state to state. Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitation on how long an implied warranty might final, so the above limitations could not apply to you. Patents pending. Lutron, Maestro Wireless, and the Sunburst emblem are registered trademarks and Radio Powr Savr is a trademark of Lutron Electronics Co., Inc. ANSI is a registered trademark of the American National Requirements Institute. IEC is a trademark of the Worldwide Electrotechnical Commission. Made and printed in the U.S.A. 25/09/09 P/N 041-172 Rev. A eight ft (2.4 m) 18 x 18 ft (5.5 x 5.5 m) thirteen ft (4.0 m) 9 ft (2.7 m) 20 x 20 ft (6.1 x 6.1 m) 14.5 ft (4.Four m) 10 ft (3.0 m) 22 x 22 ft (6.7 x 6.7 m) sixteen ft (4.9 m) 12 ft (3.7 m) 26 x 26 ft (7.9 x 7.9 m) 19 ft (5.8 m) Temporary Mounting Methods 1.1 1.2 Insert the ceiling tile mounting wire through the 2 smaller holes within the mounting bracket and change the mounting bracket. Mount Sensor to a ceiling tile by inserting the wire legs through the tile, ensuring the Sensor is flush to the tile. Word: Don't twist wire legs collectively. 1.2 After the Sensor has been temporarily mounted, go away the Sensor in place on the tile and both take the tile down or remove an adjacent tile to realize entry to the legs of the mounting wire on the back of the tile. Low Activity: This is essentially the most sensitive setting and will detect very slight motions. That is the advisable setting, as it would work properly for nearly all applications. It is good for areas where occupants will typically be seated for long periods of time. Twist the wire legs collectively tightly so the mounting bracket stays snug against the tile. This setting is barely much less sensitive than the Low Exercise setting and can be used for areas that experience regular exercise. This is the least sensitive setting and can be utilized for areas that can typically solely expertise massive motions, corresponding to foot site visitors. The Low Activity setting is the default and will carry out best for most applications. Not often, if the Sensor is placed close to external noise sources reminiscent of heating vents, air conditioning vents, or gentle bulbs, it may turn the lights on with out occupancy or keep the lights on too lengthy after vacancy. If this occurs, altering the sensitivity to Medium Exercise or High Exercise should resolve the problem. Replace the tile. Everlasting Solid Ceiling Mounting 2.1 2.2 2.Three Advanced Set-Up Operation The advanced set-up is accessed by using the buttons on the again of the Sensor. Drill two 3/16 in (4.6 mm) pilot holes for the provided screw anchors. Press the anchors into the holes and faucet flush with a hammer. To display the present setting, press and launch the specified button. An LED will illuminate briefly, indicating the current setting. Place the flat side of the mounting bracket towards the ceiling and set up the 2 offered screws using a hand screwdriver. To regulate a setting, press and hold the desired button till the LED corresponding to the current setting begins flashing rapidly, indicating the setting can now be adjusted. Each subsequent button press of lower than 2 seconds will increment the mode to the next obtainable setting. Urgent any of the opposite buttons will have no effect. To avoid wasting the selected setting, press and hold the button until the LED turns on solid, indicating the saved setting. Through the adjustment procedure, if there isn't any exercise for 30 seconds, the LEDs will flip off and no settings shall be saved. Notice: Do not over-tighten. 2.Four Attach the Sensor to the mounting bracket by inserting and twisting in a clockwise course till the Sensor locks into place. To take away the bracket from the ceiling, grasp the removing tab on the adhesive strip and pull the tab VERY SLOWLY straight across the ceiling, stretching the strip till the bracket releases from the ceiling. Discard the strip. Never pull the strip at an angle, as it might break or harm the ceiling floor. Be aware: Don't pull at an angle. Lens Masking (Optional) Every time doable, the Sensor should be put in in a location the place it can't simply see into areas outside the supposed space, akin to hallways or adjoining rooms. If this case cannot be averted, parts of the lens may be masked with the supplied labels to dam the Sensor’s view of the undesired areas. It is suggested to remove the Sensor from the mounting bracket before applying Advanced Set-Up (Non-obligatory) the masking labels. The Sensor options several superior set-up modes. For nearly all of installations, the default settings will provide one of the best efficiency and also you will not need to utilize the advanced set-up. The Occupancy model of the Sensor has three adjustable advanced set-up modes: Timeout, Auto-On, and Sensitivity. The Vacancy-Solely model has solely two modes (Auto-On not accessible). The default settings are listed under. The Sensor will be screwed onto the mounting bracket in several completely different orientations. Be certain to notice the Sensor’s orientation earlier than taking it down and substitute the Sensor in the same orientation to ensure the supposed space will get blocked. Outer lens sections correspond to the detection regions furthest away from the Sensor, whereas internal sections correspond to regions closer to the Sensor. Watch out when making use of the labels to keep away from creating gaps between adjacent masked sections. The Sensor might detect movement through inadvertent gaps. All the time (Occupancy model solely) Timeout 30 min 15 min 5 min Auto-On All the time Low light Disable Exercise Timeout 30 min 15 min 5 min Advanced Set-Up Modes Auto-On Always Low mild Disable Exercise Exercise: Low Activity Lens sections proven in white are masked with labels Timeout The Sensor will flip the lights off if no motion occurs during the timeout interval. There are three obtainable timeout settings: 5, 15, and half-hour. Lens Mask Lens sections shown in gray haven't been masked Auto-On The automated-on functionality of the Sensor could be adjusted to manage how the lights reply upon preliminary occupancy. There are three available settings: Always, Low mild, and Disable. At all times: The lights will always activate. Testing Sensor Coverage With the Sensor mounted on the ceiling, press and release the "Test: Sensor" button on the entrance of the device. The lens will glow briefly, indicating the test mode has been entered. Be aware: There is a warm-up interval of roughly 40 seconds after the batteries are put in earlier than the check mode might be activated. If the button is pressed during this time, the lens will flash continuously till the heat-up interval is full, and then the test mode will likely be robotically entered. Verify the coverage area by walking through the space and observing the lens. The lens will glow strong each time movement is detected. If the lens remains off during movement, the Sensor can not detect movement at that location. Press and release the "Test: Sensor" button once more to exit the check mode. If the button is just not pressed, the take a look at mode will automatically day out quarter-hour after being enabled, or 5 minutes after the last detected motion if the room is vacated. If the Sensor has important hassle detecting motion in the course of the test, it ought to be moved to another location and retested. If the Sensor nonetheless has poor detection from the brand new location, discuss with the Troubleshooting section. Non permanent Drop Ceiling Mounting Use this process if the Sensor can be mounted on a ceiling tile. The ceiling tile mounting wire is offered for each short-term and permanent mounting of the Sensor to drop ceilings composed of a number of tiles. It is designed to allow momentary mounting, testing, and repositioning (if mandatory) of the Sensor with out damaging a ceiling tile. Once the Sensor’s closing place has been chosen, the mounting wire can be twisted to lock the Sensor in place permanently. If the Sensor coverage and wireless communication exams have been efficiently accomplished, use the mounting bracket as a template to mark the screw gap places with a pencil. Notice: Pull very slowly. Max. Room Dimensions Radius of Coverage for Complete Coverage at Floor If you're uncertain about correctly positioning the Sensor, the next non permanent mounting and testing procedures are really helpful to confirm proper performance earlier than completely putting in the Sensor. Sensor’s detection range is dependent on the ceiling top, as shown in the desk under. Discover: Do not disassemble, crush, puncture, or incinerate the batteries. Do not dispose of batteries in regular family waste. Please recycle, take to a proper battery disposal facility, or contact your local waste disposal provider relating to local restrictions on the disposal or recycling of batteries. O NOT mount the Sensor within 4 ft (1.2 m) of HVAC vents or gentle bulbs installed below the ceiling line. Hotter rooms may cut back the Sensor’s capacity to detect occupants. Use only high-quality lithium batteries, dimension CR123, 3 V (ANSI-5018LC, IEC-CR17345). Don't use rechargeable batteries. Utilizing improperly rated batteries could injury the Sensor. For questions concerning the set up or operation of this product, name the Lutron Technical Help Heart. Please present actual model number when calling. U.S.A. and Canada (24 hrs / 7 days) Setting the Occupancy Mild Stage (occupancy version, dimming devices solely) the Sensor to the mounting bracket by inserting and twisting in a clockwise 2.5 Attach path till the Sensor locks into place. Sensor coverage and wireless communication tests as described in 2.6 Perform sections E. Testing Sensor Protection and F. Testing Wireless Communication. The Sensor ought to be installed in a location the place it has an excellent view of all parts of the room. The Sensor requires line of sight to function properly. If you can't see the Sensor, it can not see you. The Sensor can't see by means of glass objects reminiscent of patio or shower doors. The range and efficiency of the RF system is very dependent on a wide range of complicated components such as: · Distance between system parts · Geometry of the building construction · Building of walls separating system elements · Electrical gear located near system elements Technical Help 2.2 Establish a location on the ceiling where the Sensor could have a very good view of the room. 2.Three Take away the black "wall side" liner from the adhesive strip. The Sensor is designed for ceiling use solely. Do not set up on ceilings increased than 12 ft (3.7 m) or non-ceiling surfaces. Doing so may considerably inhibit the Sensor’s performance. 4. Do not paint Sensor. · · · · The "Lights On" and "Lights Off" buttons should now change the lights within the room on and off, respectively, when pressed. Repeat the above process to set up the Sensor with any extra gadgets. The Sensor is intended for indoor use solely. Operate between 32 °F and 104 °F (0 °C and forty °C). 1.1 a number of seconds. Sensor that has been set up. After approximately 6 seconds, the lens will flash quickly a number of occasions, indicating the light level has been saved. All Sensors arrange with the Dimmer will now use the saved occupancy gentle level. 2. Clean Sensor with a soft damp cloth solely. Don't use any chemical cleaners. Notice: This equipment has been examined and found to comply with the boundaries for a category B digital gadget, pursuant to part 15 of the FCC guidelines. These limits are designed to provide affordable safety against dangerous interference in a residential installation. This gear generates, uses and may radiate radio frequency energy and, if not put in and used in accordance with the directions, may cause harmful interference to radio and tv reception, which may be decided by turning the gear off and on. The consumer is inspired to attempt to appropriate the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Enhance the separation between the equipment and receiver. Connect the tools into an outlet on a circuit different from that to which the receiver is linked. Seek the advice of the seller or an skilled radio/Tv technician for assist. Caution: Adjustments or modifications not expressly authorized by Lutron Electronics Co. could void the user’s authority to operate this equipment. This system complies with Half 15 of the FCC rules. This machine should settle for any interference received, together with interference that will cause undesired operation. Swap 2.1 Set the Dimmer to the desired light level for coming into the room. 2.2 Save holding the "Lights On" button on the front of a Note: For both Sensor model, the lights will also be manually turned off at any time by utilizing the dimming or switching gadget immediately. Necessary Notes or Add the Sensor to the Dimmer or Change by urgent and holding the "Lights Off" button on the entrance of the Sensor for roughly 6 seconds till the lens flashes briefly. The lights within the room will even flash three occasions, indicating the Sensor has been successfully added. The Dimmer or Switch will exit set-up mode mechanically. The sensitivity of the Sensor could be adjusted based on the anticipated level of activity within the room. There are three out there exercise settings: Low Activity, Medium Activity, and Excessive Activity. Everlasting Drop Ceiling Mounting Word: Leave the elimination tab uncovered past the edge of the bracket so it may be accessed for removal later. 6 seconds until all LEDs on the gadget begin flashing. Launch the tap button. Sensor is detecting movement in areas that aren't desirable, similar to hallways or adjacent rooms, consult with section I. Lens Masking. If Sensor detection is satisfactory during this check, perform the wireless communication test as described in section F. Testing Wireless Communication. Testing Wireless Communication This test should be carried out to verify that the Sensor has been appropriately arrange with the corresponding dimming or switching gadget and that there's proper wireless communication from the chosen Sensor location. If the lights within the room are usually not on, turn them ON manually at the dimming or switching machine. Press and release the "Lights Off" button on the entrance of the Sensor. The lights should flip OFF. Press and launch the "Lights On" button on the entrance of the Sensor. The lights should turn on. If the lights don't reply accurately, consult with the Troubleshooting section. Low gentle: The lights will only turn on mechanically upon entry if there is just not already adequate ambient light in the room. Hallway falls within Sensor’s coverage space. Disable: This setting converts the Sensor to vacancy mode. The lights will not automatically turn on but will nonetheless mechanically turn off after vacancy. The lights should be manually turned on by utilizing the associated dimming or switching machine. Observe: The 15-second vacancy grace interval is lively on this mode. Seek advice from the Sensor Operation section originally of this document for more details. Troubleshooting Symptom Possible Causes Solution Lights don't activate when space is occupied. Sensor will not be correctly added to dimming / switching machine(s). Sensor’s Auto-On setting is about to "Low light" or "Disable". The lights were lately turned off manually and the timeout has not yet expired. Sensor does not have full view of room. Sensor is exterior wireless vary of dimming/switching device. Confer with section B. Set-Up. Consult with part H. Superior Set-Up. Dimming/switching system has been improperly wired. Gentle bulb(s) burned out. Breaker is off or tripped. Sensor’s timeout is too short for this application. Sensor does not have full view of room. Lens mask is improperly applied. Sensor’s sensitivity is simply too low. Sensor’s timeout has not yet expired. An external noise supply resembling an HVAC vent is interfering. Confer with section A. Pre-Installation. Habits of lights does not match Sensor settings. Sensor coverage extends past room perimeter. The intended setting was not saved. Multiple Sensors are added to a dimming/switching device and their settings do not match. Refer to part A. Pre-Set up. Refer to section C. Sensor Placement or I. Lens Masking. Confer with part H. Advanced Set-Up. Consult with section H. Superior Set-Up. Sensor lens does not glow in response to motion throughout Sensor protection testing. Sensor cannot see motion attributable to obstruction. Room is simply too massive or oddly formed. Transfer Sensor to another location. Check with section C. Sensor Placement. A number of Sensors could also be necessary for full room protection. Strive moving Sensor to a new location or decreasing sensitivity. Confer with section C. Sensor Placement or H. Superior Set-Up. Lights flip OFF whereas house is occupied. Lights keep ON after house is vacated. Lens doesn't cease glowing during Sensor coverage testing even when there is no such thing as a movement. Lights do not respond correctly throughout wireless communication testing. Sensor lens flashes and lights do not turn on when space is occupied. Battery has been installed incorrectly. An exterior noise supply comparable to an HVAC vent is interfering. Confer with section C. Sensor Placement. Confer with section C. Sensor Placement or F. Testing Wireless Communication. Seek advice from part H. Advanced Set-Up. Seek advice from part C. Sensor Placement. Discuss with part I. Lens Masking. Discuss with section H. Advanced Set-Up. Seek advice from part H. Advanced Set-Up. Attempt moving Sensor to a new location or decreasing sensitivity. Discuss with part C. Sensor Placement or H. Advanced Set-Up. Sensor will not be accurately added to dimming / switching gadget. Sensor is outdoors wireless range of dimming/switching device. Seek advice from part B. Set-Up. Move Sensor closer to dimming/switching machine and retry test. Seek advice from part F. Testing Wireless Communication. Battery has been put in incorrectly. Dimming/switching system has been improperly wired. Mild bulb(s) burned out. Breaker is off or tripped. Battery is low. Discuss with section A. Pre-Installation. Remove sensor from take a look at mode. Check with part E. Testing Sensor Protection.